Vollrath M202B Water Cooled Manuel d'utilisateur

Model M202 IntelliTecOPERATORS MANUALManual No. 513666 Rev.1

Owner’s Manual #513666 Rev.1 4 M202B Model Machines3 Insulate the suction line with a minimum of 3/8” wall thickness or the wall thickness required

Owner’s Manual #513666 Rev.1 5 M202B Model MachinesD. RECEIVING AND INSTALLING REMOTE CONDENSING UNITSNOTEThe remote condensing units may be sent pr

Owner’s Manual #513666 Rev.1 6 M202B Model Machines4 Connect the refrigeration lines from the line sets to the machine. Access the machine from the

Owner’s Manual #513666 Rev.1 7 M202B Model Machines5. Set the pressures for the remaining cylinders.NOTEIf the machine is water-cooled, the dischar

Owner’s Manual #513666 Rev.1 8 M202B Model Machines

Owner’s Manual #513666 Rev.1 9 M202B Model MachinesSECTION 3INITIAL SET-UP AND OPERATION3.1 OPERATOR’S SAFETY PRECAUTIONS SAFE OPERATION IS NO ACCID

Owner’s Manual #513666 Rev.1 10 M202B Model MachinesB. Product Selector Switch The product selector switch changes the refrigeration profi le of th

Owner’s Manual #513666 Rev.1 11 M202B Model Machines3.3 SANITIZINGSanitizing must be done after the machine is cleaned and just before the hopper is

Owner’s Manual #513666 Rev.1 12 M202B Model MachinesG. Turn the fl ow control knob clockwise to the 2:00 position. A small amount of mix and remainin

Owner’s Manual #513666 Rev.1 13 M202B Model MachinesB. Place all parts in the solution and clean with provided brushes.C. Wash the hopper and free

Owner’s Manual #513666 Rev.1 14 M202B Model MachinesE. Lubricate the inside and outside of the front wear bushing with Petrol Gel and install it on

Owner’s Manual #513666 Rev.1 15 M202B Model MachinesDrive Belt Wear and TensionInspect the drive belts for wear. Check for wear marks from the belts

Owner’s Manual #513666 Rev.1 16 M202B Model Machines

Owner’s Manual #513666 Rev.1 17 M202B Model MachinesSECTION 4TROUBLESHOOTING4.1 ERROR CODESWhen the machine experiences a problem, one of the follow

Owner’s Manual #513666 Rev.1 18 M202B Model MachinesError Code 5 - Freezing Cylinder Sensor The Freezing Cylinder Sensor Error (E5) indicates a fai

Owner’s Manual #513666 Rev.1 19 M202B Model Machines4.3 TROUBLESHOOTING TABLESPROBLEM POSSIBLE CAUSE REMEDYCustard is running too cold or auger blad

Owner’s Manual #513666 Rev.1 20 M202B Model Machines

Owner’s Manual #513666 Rev.1 21 M202B Model MachinesSECTION 5REPLACEMENT PARTS Part Description Quantity BR-0020 Brush - Tubing (1/2”) 1 BR-00

Owner’s Manual #513666 Rev.1 22 M202B Model Machines5.2 AUGER SHAFT AND FACEPLATE PARTS Part Description Quantity C-2000-50 Spring 10 per barre

Owner’s Manual #513666 Rev.1 23 M202B Model Machines Part Description Quantity 754021 Tube - Flow Control (Hopper) 1 per barrel 2202565 Tray

This manual provides basic information about the machine. Instructions and suggestions are given covering its operation and care.The illustrations and

Owner’s Manual #513666 Rev.1 24 M202B Model Machines

September 1, 2007 Form 721-053, Rev.01 Page 1 of 1 ROSS & TELME WARRANTY 1. Scope: Stoelting, LLC warrants to the first user (t

Safety Alert Symbol:This symbol Indicates danger, warning or caution. Attention is required in order to avoid serious per-sonal injury. The message th

Section Description Page 1 Description and Specifi cations 1.1 Description ...

Owner’s Manual #513666 Rev.1 1 M202B Model Machines1.1 DESCRIPTIONThe M202 is continuous fl ow custard machine. It is equipped with fully automatic

Owner’s Manual #513666 Rev.1 2 M202B Model Machines1.2 SPECIFICATIONSM202B A/C M202B A/C Remote M202B W/CDimensionsMachine with crate Machine with c

Owner’s Manual #513666 Rev.1 3 M202B Model MachinesSECTION 2INSTALLATION INSTRUCTIONS2.1 SAFETY PRECAUTIONSDo not attempt to operate the machine unt